| CNV-3636 |
|
 |
36 fully independent SAS and SATA ports |
|
Supports SSP, SMP, and STP target and initiator |
|
Supports SATA
|
|
Supports multiple data rates and auto negotiation |
|
1.5G and 3.0Gb/s SAS and SATA |
|
Provide low latency connection router with crossbar module to efficiently create and maintain connections |
|
SATA/SAS HDD spin up sequencing per Phy basis |
|
LEDs indicate SAS Port Activity |
|
Allows concurrent connections to SAS or SATA targets |
|
Programmable a scalable interface that supports up to 1024 SAS addresses |
|
Supports wide and narrow port configurations |
|
Phy-based zoning for system security: allows re-use of routing table resources across all phys |
|
Includes high performance active cooling higher system reliablity |
|
Port independent auto negotiation |
|
Ports are non denominational for initiator or target connect |
|
EPP port for management |
|
Support Direct, Subtractive decode, and Table routing |
|
Supports SATA/STP data transfers of 1.5Gb/s |
|
Allows addressing of multiple SATA targets |
|
Allows multiple initiators to address a single target |
| |
|
| CNV-1212 |
|
| SAS Expander Features: |
|
Supports SSP, STP, and SMP standards |
|
Supports SATA |
|
Supports multiple data rates and auto negotiation
- 1.5Gb/s and 3.0Gb/s SAS
- 1.5Gb/s SATA
|
|
Provide low latency connection router |
|
Provides configurable drive spin-up sequencing on per phy basis |
|
LEDs indicate SAS Port Activity & Fault |
|
Allows concurrent connections to SAS or SATA targets |
|
Programmable a scalable interface that supports up to 144 devices through multiple expanders |
|
Provides a Serial I/O interface for managing general purpose data communication |
| STP/SATA Features: |
|
Supports SATA/STP data transfers of 1.5Gb/s |
|
Allows addressing of multiple SATA targets |
|
Allows multiple initiators to address a single target |
| SMP Features: |
|
Decodes SMP packets that are destined for the expander |
|
Performs CRC checking and generation on the request frames and response frames |
| |
|
| |
|
| |
|
| |
|
| |
|
| |
|
| CNV-6898 |
|
|
1 Year Warranty |
|
48 MA Single-Ended Active Negation Drivers |
|
Data Deskewing Circuitry |
|
Data transfers up to 40 Mbytes/second |
|
Does not occupy a SCSI ID |
|
Four independent SCSI Expanders |
|
Four SCSI Activity LEDs |
|
LVD to HVD or single-ended to HVD conversion
|
|
Meets ANSI SCSI X3.131-1994 and X3.277-1996
Specifications, X3.T10/1142D SPI-2 (Ultra2 SCSI), X3.T10/1302D SPI-3
(Ultra3 SCSI) and X3.253 SPI-4 (Ultra4 SCSI) Documents, and Compliant
with SCSI EPI Specifications. |
|
RS485DE HVD Transceivers |
|
Supports Arbitration, Parity and Disconnect/Reconnect |
|
Supports up to 16 SCSI devices |
|
Switchable HVD and LVD Termination |
|
Synchronous or Asynchronous Data Transfers
|
|
Target or initiator on either side |
|
TERMPWR via resetting circuit protector
and backflow preventing diodes |
|
Transparent Operation (No Software Required) |
|
WIDE (16-bit SCSI Bus) |
| |
|
| |
|
| CNV-6890 |
|
|
Supports Cyclic Redundancy Check |
|
Supports Double Clock Transition |
|
Data transfers up to 160 Mbytes/second
|
|
Supports Quick Arbitration and Selection
|
|
Supports Domain Validation |
|
Up to 3 Expanders can be cascaded |
|
Dynamically tunes itself to the device
process, voltage and temperature |
|
WIDE (16-bit SCSI Bus)· Supports
up to 16 SCSI devices |
|
Transparent Operation (No Software Required)
|
|
Data Deskewing Circuitry |
|
48 MA Single-Ended Active Negation Drivers
|
|
Supports Arbitration, Parity and Disconnect/Reconnect
|
|
Switchable LVD/SE Termination |
|
Allows for bus isolation by disabling
SCSI transfers |
|
Meets ANSI SCSI X3.131-1994 and X3.277-1996
Specifications, X3.T10/1142D SPI-2 (Ultra2 SCSI) and X3.T10/1302D
SPI-3 (Ultra3 SCSI) Documents |
|
Busy LED· LVD/SE Mode LED for each
side |
|
Synchronous or Asynchronous Data Transfers
|
|
Does not occupy a SCSI ID |
|
Target or initiator on either side |
|
LVD to LVD or SE to LVD conversion·
TERMPWR via resetting circuit protector and backflow preventing diodes
|
| |
|
| |
|
| CNV-6895 |
|
|
WIDE (16-bit SCSI Bus) |
|
Data transfers up to 40 Mbytes/second
|
|
Supports up to 16 SCSI devices |
|
Transparent Operation (No Software Required)
|
|
Data Deskewing Circuitry |
|
48 MA Single-Ended Active Negation Drivers
|
|
RS485DE HVD Transceivers |
|
Supports Arbitration, Parity and Disconnect/Reconnect
|
|
Switchable HVD and LVD Termination |
|
Meets ANSI SCSI X3.131-1994 and X3.277-1996
Specifications, X3.T10/1142D SPI-2 (Ultra2 SCSI) Document |
|
Busy LED |
|
Synchronous or Asynchronous Data Transfers
|
|
Does not occupy a SCSI ID |
|
Target or initiator on either side |
|
LVD to HVD or single-ended to HVD conversion
|
|
TERMPWR via resetting circuit protector
and backflow preventing diodes |
|
Transparent Operation (No Software Required)
|
| |
|
| |
|
| CNV-6896 |
|
|
Peripheral Component Interconnect (PCI)
PICMG 2.0 R3.0 OCT. 1, 1999 |
|
WIDE (16-bit SCSI Bus) |
|
Data transfers up to 40 Mbytes/second
|
|
Supports up to 16 SCSI devices |
|
Transparent Operation (No Software Required)
|
|
Data Deskewing Circuitry |
|
48 MA Single-Ended Active Negation Drivers
|
|
RS485DE HVD Transceivers |
|
Supports Arbitration, Parity and Disconnect/Reconnect
|
|
Switchable HVD and LVD Termination |
|
Meets ANSI SCSI X3.131-1994 and X3.277-1996
Specifications, X3.T10/1142D SPI-2 (Ultra2 SCSI) Document |
|
Busy LED |
|
Synchronous or Asynchronous Data Transfers
|
|
Does not occupy a SCSI ID |
|
Target or initiator on either side |
|
LVD to HVD or single-ended to HVD conversion
|
|
TERMPWR via resetting circuit protector
and backflow preventing diodes |
|
Transparent Operation (No
Software Required) |
| |
|
| |
|
| CNV-6881 |
|
|
WIDE (16-bit SCSI Bus) |
|
Data transfers up to 40 Mbytes/second
|
|
Supports up to 16 SCSI devices |
|
Transparent Operation (No Software Required)
|
|
48 MA Active Negation Single-Ended Drivers
|
|
Supports Arbitration, Parity and Disconnect/Reconnect
|
|
Active Single-Ended and LVD Termination
|
|
Meets ANSI SCSI X3.131-1994 and X3.277-1996
Specifications X3.T10/1142D Document |
|
Busy LED |
|
Synchronous or Asynchronous Data Transfers
|
|
Does not occupy a SCSI ID |
|
Supports 16 Bit SCSI Arbitration |
|
Target or initiator on either side |
|
LVD to single-ended or single-ended to
single-ended |
|
WIDE single-ended peripherals |
|
WIDE Low Voltage Differential |
|
TERMPWR via resetting circuit protector
and backflow preventing diodes Data Deskewing Circuitry |
| |
|
| |
|
| CNV-6868 |
|
|
Transparent Operation (No Software Required)
|
|
Data Deskewing Circuitry |
|
Differential Termination |
|
WIDE (16-bit SCSI Bus) |
|
UltraSCSI Data Transfers up to 40 Mbytes/second
|
|
Supports up to 16 SCSI Devices |
|
48 MA Single-Ended Active Negation Drivers
|
|
RS485 Differential Transceivers |
|
Differential Cable Lengths Up to 60 Meters
(200 feet) |
|
Supports Arbitration, Parity and Disconnect/Reconnect
|
|
Active Single-Ended Termination |
|
Meets ANSI SCSI X3.131-1986 and X3.131-199x
Specifications |
|
Busy LED |
|
Synchronous or Asynchronous Data Transfers
|
|
Single-ended and Differential Termination
Power |
|
Does not Occupy a SCSI ID |
|
Includes Y-power cable |
|
Automatic Resetting Remote Terminator
Power Circuit Protection |
|
Diodes Preventing Termination Power Backflow
|
|
Diffsens Differential Driver Protection
Circuitry |
|
Hot Swappable |
| |
|
| |
|
| CNV-6864 |
|
|
WIDE (16-bit SCSI bus) |
|
Ultra SCSI Data transfers up to 40 Mbytes/second
|
|
Supports up to 16 SCSI devices |
|
Transparent Operation (No Software Required)
|
|
48 mA Single-Ended Active Negation Drivers
|
|
RS485 Differential-Ended Transceivers
|
|
Differential Cable Lengths Up to 60 Meters
(200 feet) |
|
Supports Arbitration, Parity and Disconnect/Reconnect
|
|
Active Single-Ended Termination |
|
Meets ANSI SCSI X3.131-1986 and X3.131-199x
Specifications |
|
Busy LED |
|
Synchronous or Asynchronous Data Transfers
|
|
Does not occupy a SCSI ID |
|
Supports 16-Bit SCSI Arbitration |
|
Includes Y-power cable |
|
Automatic Resetting Remote Terminator
Power Circuit Protection |
|
Diodes Preventing Termination Power Backflow
|
|
Diffsens Differential Driver Protection
Circuitry |
|
Optional Single and Differential-Ended
Termination Power |
|
Optional sense Power Supply failure circuit
resets single-ended SCSI drives prior to drive failure |
| |
|